header

For Your Functional Ink & Coating Requirements

...Start Here

globeEL Panel and LED Lighting

Surface Resistivity: < .010 Ω/square/mil when fully dried

Applications:

  • Circuit and Electromechanical Assemblies
  • EL Panel and LED Lighting
  • Membrane switch
  • Touch screens
  • Printed Heaters
  • Other printed electronic applications

Features:

  • Screen printable
  • Fast drying
  • Extremely tough, scuff resistant and crease resistant
  • Ideal for long traces
  • Excellent adhesion to polyester, polyimide, ITO and most other substrates
  • Compatible with our UV curable dielectrics, all of our conductive epoxy adhesives and our UV curable component encapsulants and conformal coatings

Download the AG-500A data sheet.

Surface Resistivity: < .015 Ω/square /mill when fully dried

Applications:

  • Membrane switches
  • Additive circuits
  • Printed Heaters
  • PTF Circuits
  • Defibrillator pads
  • EKG/EEG Electrodes
  • Blood glucose sensors
  • EMI/RFI applications
  • EL panels

Features:

  • Screen print
  • Fast drying
  • High conductivity
  • Thin for spray or dipping
  • Can blend with carbon to customize resistance

Download the AG-510 data sheet.

Surface Resistivity: < 0.015 Ω/square/mil

Applications:

  • Flex circuits
  • Membrane switches
  • Additive circuits
  • EMI/RFI applications
  • Thermal targets

Features:

  • Good conductivity
  • Screen print
  • Thin for spray or dipping
  • Can blend with carbon to customize resistance
  • Crease resistant

Download the AG-800 data sheet.

Surface Resistivity: > 1 x 1014 Ω-cm

Applications:

  • Capacitance layer between phosphor and back electrodes for EL lamps on polyester or ITO substrates

Features:

  • Rigid thermaldielectric
  • Electrically insulating
  • Very moisture resistant
  • Produces mirror smooth surface finish

Download the BT-101 data sheet.

Applications

  • Touch Screens
  • Electroluminescent Lamps
  • Capacitive Touch Sensors
  • Membrane Switches

Features

  • Transparent
  • Screen printable
  • For use on flexible or rigid substrates
  • Replaces fragile ITO
  • Thermoformable
  • Compatible with most products in the Applied Ink Solutions product line.

Download the Clear Conductive Inks data sheet.

Surface Resistivity: 5.0 x 1015 Ω/square

Applications:

  • EL Panels (Electroluminescent)

Features:

  • Clear binder to custom mix with commercially available phosphor powder as needed
  • Excellent flexibility, toughness & resistance to water & oxygen
  • Outstanding adhesion to ITO surfaces
  • Use with our BT-101 Barium Titanate Dielectric

Download the PH-745 data sheet.

Surface Resistivity: @25°C 2.9 x 1013 Ω/square/mil

Applications:

  • Printed insulation layers for circuits
  • Touch screens
  • El panels
  • Flexible printed substrates

Features:

  • 100% solids
  • Adheres to difficult substrates such as ITO or other metal oxides
  • Screen print, dip, roll, knife over roll, and curtain coating

Download the UV-1006S data sheet.

Surface Resistivity: @25°C 3.8 x 1014 Ω/square/mil

Applications:

  • Component encapsulation
  • Wire or component staking

Features:

  • 100% solids
  • Dot dispensable
  • Moisture resistant
  • Suitable for flexible substrates
  • Can be sprayed or dipped

Download the UV-3010 data sheet.

Surface Resistivity: 5.0 x 1014 W/square (X and Y axis only)

Applications:

  • For screen printing over conductive ink tail pins on flexible circuits and membrane switches, to provide protection for silver ink when using ZIF or crimp type metal connectors, while still maintaining electrical conductivity between the metal connector and the silver ink pin.

Features:

  • Designed to conduct electricity on the Z-axis through the thickness, and not along the width (X-Axis) or length (Y-Axis) of the printed ink.
  • Excellent strength, toughness, flexibility, inherent moisture resistance, and low odor.

Download the Z-904 data sheet.

Applied Ink Solutions Product Matrix